Avalon 1.9

[R3d2]

When downloading latests weather forecasts, then on first hours the true wind speed and course TWD, TWS is different.

[jef]

Difference between VR winds interpolation and Avalon !

[Rs_Mesrine]

Jef

est ce normal d'avoir un décalage des vents lorsqu'on prend les vents NOAA des bascules
Là je viens de télécharger et vents 0 et 3h restent sous numéro 0 et ensuite ca passe à 6

Fais l'essai stp et regarde si c'est normal, ca me semble bizarre

[R3d2]

Got tricky situation. Avalon calculating on HG close to change to C0. Everything is fine when delta is 0,1 - 0,3. When goes 0,5 Autosaiis changed to C0, with the same course lost 2 kTs for 20 min + penalty to go from HG to C0 and back from C0 to HG.

VR still not fixed option to turn off Auto Sails! All the time of the edge of knife. On such a speed, delta grow dramaticaly in 2 hours. From one cable tow till 0.5 nm.







And if there is more, than 26.68?

I'm fighting for 1st place in our country, Latvia, competition. I was 6 nm from first place. This mistake throwed back by to 10 nm.

[jef]

Hi BlueJadeOs,

Have you upgraded to 1.9.0-5 ( Posted on last saturday), cause it fix the sail "Tolerance" trouble.
Add a 1,003 coef to polar before changing sail set.

What boat have been used when importing polar from toxctt ?
The right one is "IMOCA FOILS", see other post in forum.

You may even use your on polars as i saw that our have VIP (export to csv, modify, reload from csv).

Aslo i have encouter similar trouble, and doing a full refresh of Virtual Regatta, was able to change heading without penalty.

Wishing that you win the LatVia sub race

[R3d2]

Hi BlueJadeOs,

Have you upgraded to 1.9.0-5 ( Posted on last saturday), cause it fix the sail "Tolerance" trouble.
Add a 1,003 coef to polar before changing sail set.

I'll check it out. Waiting for changed polar zones.

What boat have been used when importing polar from toxctt ?
The right one is "IMOCA FOILS", see other post in forum.

Yes. I have it.

You may even use your on polars as i saw that our have VIP (export to csv, modify, reload from csv).

Ok. Sometimes is easier to complain. Sorry! Thank you for patience! You gave us so such a great tool! You are the best!

Aslo i have encouter similar trouble, and doing a full refresh of Virtual Regatta, was able to change heading without penalty.

Wishing that you win the LatVia sub race

Refresh and reload on VR it's routine. Already sent a bunch complains to VR support. They answered, that they will fix it.

One more time, Thank you Jef for your support and work. Is it possible how some support you from user side?

[jef]

@BlueJadeOs,

Win the race, for sure AvalonVirtual/Offshore will be much more known to real/virtual skippers !

[R3d2]

Houston, we have a problem


AvalonVirtual-1.9-5

[jef]

This was a mess with VR datas, an updated version is just ready for new ZEA, see my previous post

Cheers

[R3d2]

I stucked on the Exclusion zone. Trying to Compute route.
Heading 118 . Router calculating as I'm going to 58.
Going to 58. Router thinks that I'm going on 118 and calculate further.
I almoust lost at least 2 miles. Tried to change a course. Choosed wrong course. Made calculation on new place and got again wrong direction.

[jef]

If you cross the ZE, Avalon is in deep shit cause it cannot cross it back, so you would better :
A ) Manualy handle the case, to get back above the ZE, so routing will work
B ) Remove the ZE, compute a route with a waypoint above the ZE, and then after re import ZE

Ok ?
Can't see your boat on VR, what's his name ?

[R3d2]

If you cross the ZE, Avalon is in deep shit cause it cannot cross it back, so you would better :
A ) Manualy handle the case, to get back above the ZE, so routing will work
B ) Remove the ZE, compute a route with a waypoint above the ZE, and then after re import ZE

Hardly trying not to cross ZE. Previous VR I played without router. With ruller on the screen.

Ok ?
Can't see your boat on VR, what's his name ?

Boat name: BlueJadeOs
You can see on the Avalon Router

[R3d2]

Jef, you did't understood problem. Try to go to close Exclusion zone, when angle of exclusion zone line would be 45 degrees. The General route is behind exclusion zone. From exclusion zone 10 to my be 30 min away all the time router wish to go closer to exclusion zone after route recalculation.

[jef]

Hello BlueJadeOs,
Yep following your boat.

The General route is behind exclusion zone. From exclusion zone 10 to my be 30 min away all the time router wish to go closer to exclusion zone after route recalculation.

Is this a refresh effect, not refreshing the VR screen with SYNC symbol upper right of screen, may lead to erroneous starting positions when computing route.

If we do not understand each other, maybe cause you and i are not speaking the same language, could you do some screen shots.

A+

[jef]

@R3D2,

Think i am hit by the bug now !

Capture d’écran 2020-12-04 à 13.52.23.png

Seems a discontinuity in this fuck.... ZE !

[jef]

This is a bug int the router DLL, try to fix it tonight

Seems only on OSX/Linux code

[R3d2]

Updated latest .jar

[jef]

Hello,

AvalonVirtual routing map is not excatly the same as VR one, to see the little differences, choose AvalonRoutingCarto in the map viewer.

[R3d2]

Hello,

AvalonVirtual routing map is not excatly the same as VR one, to see the little differences, choose AvalonRoutingCarto in the map viewer.

[R3d2]

~02:07 UTC +0200 Good time to crash.